10 Top Tips For Plastic Injection Molding Making

Release time:2020-03-13
10 Top Tips For Plastic Injection Molding Making

1)Make sure the project manager, mold designer and mold maker are all on the same page.

It helps immensely to take some time at the outset of a job to have a meeting where the big picture is discussed. It is always much easier to work on the various aspects of the job when you have a clear idea of what is required.
Many hours are wasted when several people figure out the same problem independently. Mistakes can be minimized by going over the procedure together, plus everyone knows who is responsible for what.
2)Do not skimp on the design
Some shops do not have an in-house designer and must outsource their design work. This is fine and works quite well- unless the boss decides to save money by cutting costs on the design. This is just asking for trouble.
Even with a high quality mold design, injection mold making is fraught with potential problems. When the design is faulty or missing details it can eat up the profit margins very quickly. For example: simple features, such as the radii that interfere in a shut-off area, can be very time consuming to troubleshoot and handwork at the end of the job.
The fit of precision holes to their components is another rather common omission in mold designs as well. Often this does not show up until assembly, at which time the mold maker must make new components or modify existing ones.
Another overlooked area is the draft angles of molding surfaces. The mold maker might not question the design when no draft is specified, and as a result the part will not eject in molding. Draft angles are obviously much easier to machine before the mold is finished!

3)Concentrate on what you do best
Every shop has it’s own strengths and weaknesses. Do what you do best and leave the rest is usually good advice. You may really want to learn something like horizontal milling, but does it make sense to sacrifice your limited time and energy?
4)Use 3D models or prototypes to clarify
As a mold maker, I’ve never understood why some bosses are so reluctant to allow the mold maker five minutes to familiarize himself with the molded part he is about to build a mold for. This would save a lot of visualizing and guessing. It is always much easier to begin with the end in mind.
5)Use standardized components
Why spend precious mold making time machining standardized components? You can almost always buy high quality components at a very competitive price.
The most foolish example of this, that I have seen, was a series of ejector pins that were ground to a smaller size. It must have taken hours to do this, and they could have bought them off the shelf for a fraction of the shop time they used.
6)Do not skimp on the mold base
It might be tempting to save a lot of money by buying a cheap mold base, but this almost always leads to problems. Some of the problems might include misaligned pockets, out of square plates, incorrect plate thickness, misaligned pins and bushing, etc.
I have worked on discount mold bases that required so much re-machining that the initial savings quickly vanished. Not only that, it is very demoralizing to work with junk when you are trying to produce quality.
7)Clarify from the outset who is responsible
This would seem to be obvious, but in many shops the communication is so poor that it is just assumed that everyone knows what is going on.
A good way to do this is with the break-out meeting or posting it on a bulletin board along with other pertinent information about the shop goings on.
8)Make sure everything is correctly ordered and available
Few things can send everyone scrambling like discovering that nobody ordered this or that. Of course, this usually is discovered at the end of the job,when there is no time left for shipping.
9)Do not waste time on meaningless precision
Sure, an injection mold is a highly precise tool, but is it really necessary for the ejector pin plate to be ground to .0002 tolerances? Many hours can be wasted on such details that do absolutely nothing to make the mold better.
We Chat: Venus
We Chat: Venus
We Chat: Nicole
We Chat: Nicole
We Chat: Phil
We Chat: Phil

Get In Touch or Get A Quote

+86-755-29667661 Moble,What's app, Wechat: (+86) 18675501860